BEAM iSERIES WebUI - Events Log



Summary

The Events Log windows display records of such event as logins, reboots, resets, connections, configuration changes and more.


Events Reporting

The Events Reporting section gives you the ability to configure rules that will inform you via SMS or email when certain events occur on your router. These events can be almost anything – configuration changes, reboots, new connections, various status updates, etc.


Events Reporting Configuration

Events Reporting Configuration is used to create and customize Events Reporting Rules. Here you can specify any event type and subtype, chose whether you want to be informed by an SMS message or email, modify what kind of information you want receive should an event occur. To open this window, choose an Event type, Event subtype and Action and click the Add button. A new rule should appear in the Events Reporting Rules tab. Click the Edit button located next to that rule after which you will be redirected to that rule's configuration window.

Send SMS




 Field Name
 Value
 Description
 Enable  yes | no; Default: no  Toggles the rule ON or OFF
 Event type
 Config change | New DHCP client | FW upgrade | Mobile data | SMS | SIM switch | Signal Strength | Reboot | SSH | WebUI | New WiFi client | LAN port state | Backup | Restore point | GPS;

Default: Config change

 The type of event that you wish to receive information about
 Event subtype
 Sample: After unexpected shut down  Specified event's sub-type. This field changes in accordance with Event type
 Action  Send SMS | Send email; Default: 
 Send SMS
 Action that is to be taken after the specified event occurs
 Enable delivery retry  yes | no; Default: no  Toggles delivery retry On or OFF. If for some reason the message delivery
 is unsuccessful, the router initiates a retry if this field is enabled
 Retry interval  1 min. | 5 min. | 10 min. | 15 min. |
 30 min. | 60 min.; Default 5 min.
 Specifies when the router should try re-sending the message in case the first attempt was a failure
 Retry count  2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10; Default: 2  Specifies the maximum number of failed attempts after which the router does not try to send the message anymore
 Message text on Event  string; Default: Router name - %rn; Event type - %et; Event text - %ex; Time stamp - %ts;  Specifies the text that the message will contain
 Get status after reboot  yes | no; Default: no  Specifies whether the router should send an SMS message indicating the
 router's status after the reboot in addition to the original message
 Status message after reboot  string; Default: Router name - %rn; WAN IP - %wi; Data Connection state - %cs; Connection type - %ct; Signal strength - %ss; New FW available - %fs;  Specifies the text that the status message will contain. This field becomes visible only if Get status after reboot is checked
 Recipients  Single number | User group; Default: Single number  Specifies the intended recipients. A guide on how to create a User group can be found in the SMS Utilities chapter, User Groups section
 Recipient's phone number  phone number; Default: " "  The intended recipient's phone number. To add more than one number, click the green Services sms gateway auto reply plus symbol.PNG plus symbol located to the right of this field. The phone number must be entered in the international format, but without dash symbols or spaces, e.g., +44061234567

Send Email



 Field Name
 Value  Description
 Enable  yes | no; Default: no  Toggles the rule ON or OFF
 Event type
 Config change | New DHCP client | FW upgrade | Mobile data | SMS | SIM switch | Signal Strength | Reboot | SSH | WebUI | New WiFi client | LAN port state | Backup | Restore point | GPS;

Default: Config change

 The type of event that you wish to receive information about
 Event subtype
 Sample: After unexpected shut down  Specified event's sub-type. This field changes in accordance with Event type
 Action  Send SMS | Send email; Default: Send SMS  Action that is to be taken after the specified event occurs
 Enable delivery retry  yes | no; Default: no  Toggles delivery retry On or OFF. If for some reason the message delivery is
 unsuccessful, the router initiates a retry if this field is enabled
 Retry interval
 1 min. | 5 min. | 10 min. | 15 min. | 30 min. | 60 min.; Default 5 min.  Specifies when the router should try re-sending the message in case the first
 attempt was a failure
 Retry count
 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10; Default: 2  Specifies the maximum number of failed attempts after which the router does not
 try to send the message anymore
 Subject  string; Default: " "  Specifies the subject of the email message
 Message text on Event  string; Default: Router name - %rn; Event type - %et; Event text - %ex; Time stamp - %ts;  Specifies the text that the message will contain
 Get status after reboot  yes | no; Default: no  Specifies whether the router should send an SMS message indicating the router's status after the reboot in addition to the original message. If this is checked you will be prompted to enter the text that the status message should contain
 SMTP server
 ip | host; Default: " "  Sender's email service provider's SMTP server. If you don't know the SMTP server's address, you can easily look it up online since it is public information
 SMTP port
 integer [0..65535]; Default: " "  Sender's email service provider's SMTP port. If you don't know the SMTP server's port, you can easily look it up online since it is public information
 Secure connection
 yes | no; Default: no  Toggles secure connection feature ON or OFF (use only if the email service provider's server supports SSL or TLS)
 Username  string; Default: " "  Sender's email account's login user name
 Password  string; Default: " "  Sender's email account's login password
 Sender's email address  email; Default: " "  The email address of the sender, i.e., the report message will be sent from this email. Make sure this is the same email that you provided login information to
 Recipient's email address  email; Default: " "  The intended recipient's email address. To add more than one email address, click the green Services sms gateway auto reply plus symbol.PNG plus symbol located to the right of this field
 Send test mail  -  Sends a test mail using the information that you provided. Once you click this button, the router will login to the provided email account and send the specified message to the specified address(-es). You should always send a test mail before finishing the configuration to make sure that everything is in order

Event Types and Sub-types


The examples provided above are both concerning the Reboot Event type and After unexpected shut down sub-type. This section is an overview of all other Event type and sub-types.
Config change
 ENEBT SUB-TYPE  DESCRIPTION
 All  Sends a report message when any type of configuration changes are applied
 SMS  Sends a report message when any SMS related configuration changes are applied. For example, whenever a new SMS Utilities rule is created or changed, changes are made to Auto Reply or Remote configurations, etc.
 Mobile traffic
 Sends a report message when Mobile Traffic Logging is enabled/disabled or logging interval is changed.
 Multiwan  Sends a report message when changes to WAN Backup configuration are applied. For example, whenever a switch from using Wired as main WAN to backup WAN occurs, Wireless is added as a Backup WAN, Health monitor configurations are changed, etc.
 Mobile  Sends a report message when any Mobile configuration changes are applied. For example, whenever Service mode, APN, Connection type is changed, etc.
 Data limit
 Sends a report message when any Mobile Data Limit configuration changes are applied. For example, whenever new data limit is configured, data limit gets disabled/enabled on SIM1/SIM2, data limit period is changed, etc.
 GPS  Sends a report message when any configuration changes concerning GPS are applied. For example, whenever GPS gets enabled/disabled, Remote host/IP address is changed, new Geofencing area is defined, etc.
 Events reporting  Sends a report message when any configuration changes to Events Reporting are applied. For example, whenever a new Events Reporting Rule is created, changed, deleted, etc.
 Periodic reboot  Sends a report message when any configuration changes to Periodic Reboot are applied. For example, whenever Periodic Reboot gets enabled/disabled, Periodic Reboot interval is changed, etc.
 Ping reboot
 Sends a report message when any configuration changes to Ping Reboot are applied. For example, whenever Ping Reboot gets enabled/disabled, host to ping has changed, etc.
 Auto update  Sends a report message when any configuration changes to Auto update are applied
 Site blocking
 Sends a report message when any configuration changes to Site Blocking are applied. For example, whenever Whitelist is changed to Blacklist or vice versa, a new entry is added to Blacklist/Whitelist, etc.
 Hotspot  Sends a report message when any configuration changes to Hotspot are applied. For example, whenever Hotspot SSID was changed, Radius server was changed, Hotspot was enabled/disabled, etc.
 Content blocker   Sends a report message when any configuration changes to Proxy Based Content Blocker are applied. For example, whenever Whitelist is changed to Blacklist or vice versa, a new entry is added to Blacklist/Whitelist, etc.
 Login page  Sends a report message when any Language Settings are changed
 Language  Sends a report message when any Language Settings are changed
 Profile  Sends a report message when a new Profile is added or deleted
 DDNS  Sends a report message when any configuration changes to Dynamic DNS are applied. For example, whenever a new DDNS instance is created, changed, deleted or edited
 Access control  Sends a report message when any configuration changes to Access Control are applied. For example, SSH/HTTP/HTTPS remote or local access is enabled/disabled, changes are made to SSH or WebUI Access Secure, etc.
 DCHP  Sends a report message when any configuration changes to DHCP are applied. For example, whenever DHCP Server is enabled/disabled, DHCP address range is changed
 SSH  Sends a report message when any configuration changes to SSH are applied
 Network  Sends a report message when any Network related configuration changes are applied. For example, whenever Main WAN is changed, LAN IP address is changed, a Wi-Fi Access Point is enabled/disabled, etc.
 Wireless  Sends a report message when any configuration changes to Wireless are applied. For example, a new Wi-Fi Access point is created, deleted, enabled/disabled, SSID is changed, etc.
 Firewall  Sends a report message when any configuration changes to Firewall are applied. For example, a new Traffic rule is added, a new SNAT rule is added, a rule is disabled/enabled, etc.
 NTP  Sends a report message when any configuration changes to NTP are applied. For example, whenever NTP is enabled/disabled, Time zone is changed, etc.
 Other  Sends a report message when any configuration changes other than the ones provided above are applied

New DHCP Client
 Event sub-type
 Description
 All  Sends a report message when a new devices is connected to the router either via LAN or Wi-Fi
 Connected from WiFi  Sends a report message when a new device is connected to the router via Wi-Fi
 Connected from LAN  Sends a report message when a new device is connected to the router via LAN port

FW Upgrade
 Event sub-type  Description
 All  Sends a report message when the router initiates a Firmware upgrade (either from an uploaded FW file or from server)
 From file  Sends a report message when the router initiates a Firmware upgrade from an uploaded FW file
 From server  Sends a report message when the router initiates a Firmware upgrade from server

Mobile Data
 Event sub-type  Description
 All  Sends a report message when mobile data connection status changes (from Connected to Disconnected or vice versa)
 Connected  Sends a report message when mobile data connection is achieved
 Disconnected  Sends a report message when mobile data connection is lost

SMS
 Event sub-type
 Description
 SMS received  Sends a report message when the router receives a new SMS message

Signal Strength
 Event sub-type
 Description
 All  Sends a report message when the router's RSSI value leaves any one of the below specified ranges
 -121 dBm -113 dBm  Sends a report message when the router's RSSI value leaves the -121 dBm to -113 dBm range
 -113 dBm -98 dBm  Sends a report message when the router's RSSI value leaves the -113 dBm to -98 dBm range
 -98 dBm -93 dBm  Sends a report message when the router's RSSI value leaves the -98 dBm to -93 dBm range
 -93 dBm -75 dBm  Sends a report message when the router's RSSI value leaves the -93 dBm to -75 dBm range
 -75 dBm -60 dBm  Sends a report message when the router's RSSI value leaves the -75 dBm to -60 dBm range
 -60 dBm -50 dBm  Sends a report message when the router's RSSI value leaves the -60 dBm to -50 dBm range

Reboot
 Event sub-type  Description
 All  Sends a report message when the router starts up after any type of reboot (except factory reset)
 After unexpected shutdown  Sends a report message when the router shuts down unexpectedly and starts back up again
 From WebUI  Sends a report message when the router starts up after a reboot command is initiated from the router's WebUI Administration->Reboot section
 From SMS  Sends a report message when the router starts up after a reboot command is initiated via SMS
 From Input/Output  Sends a report message when the router starts up after a reboot command is initiated via Input/Output
 From ping reboot  Sends a report message when the router starts up after a reboot command is initiated by the Ping Reboot function
 From periodic reboot  Sends a report message when the router starts up after a reboot command is initiated by the Periodic Reboot function
 From button  Sends a report message when the router starts up after being restarted by the press of the physical button located on the router

SSH
 Event sub-type  Description
 All  Sends a report message when someone connects to the router via SSH (either successfully or unsuccessfully)
 Successful authentication  Sends a report message when someone successfully connects to the router via SSH
 Unsuccessful authentication  Sends a report message when someone unsuccessfully tries to connect to the router via SSH

WebUI
 Event sub-type  Description
 All  Sends a report message when someone connects to the router via HTTP or HTTPS (either successfully or unsuccessfully)
 Successful authentication  Sends a report message when someone successfully connects to the router via HTTP or HTTPS
 Unsuccessful authentication  Sends a report message when someone unsuccessfully tries to connect to the router via HTTP or HTTPS

New WiFi Client
 Event sub-type  Description
 All  Sends a report message when a device connects to or disconnects from the router's WLAN (Wireless Network or Wireless LAN)
 Connected  Sends a report message when a device connects to the router's WLAN
 Disconnected  Sends a report message when a device disconnects from the router's WLAN

Backup
 Event sub-type  Description
 All  Sends a report message when the router switches from using the Main WAN to using the Backup WAN and vice versa
 Switched to main  Sends a report message when the router switches from using the Main WAN to using the Backup WAN
 Switched to backup
 Sends a report message when the router stops using the Backup WAN and start using the Main WAN

Restore Point
 Event sub-type  Description
 All  Sends a report message when either when a new Restore point is created or a Restore Point is loaded in to the router
 Save  Sends a report message when a new Restore Point is created
 Load  Sends a report message when a Restore Point is loaded on to the router

GPS
 Event sub-type  Description
 All  Sends a report message when the router moves in and out of the GPS Geofence area
 Left geofence  Sends a report message when the router leaves the GPS Geofence area
 Entered geofence  Sends a report message when the router enter the GPS Geofence area

Reporting Configuration

The Reporting Configuration section lets you create rules that transfer logs to email or FTP.

Events Log Report Configuration

Events Log Report Configuration provides you with the ability to change the configuration of periodic events reporting to email or FTP. You can access it by creating a rule and clicking the Edit button next to it, just like Event Reporting Configuration.

FTP

 Filed Name
 Value  Description
 Enable  yes | no; Default: no  Toggles the log file report rule ON or OFF
 Events log  System | Network | All; Default: System  Specifies which log to transfer
 Transfer type  Email | FTP; Default: Email  Specifies whether to transfer the log(s) to FTP or Email
 Compress file  yes | no; Default: no  Compress events log file using gzip
 Enable delivery retry  yes | no; Default: no  Toggles delivery retry On or OFF. If for some reason the message delivery is unsuccessful, the router initiates a retry if this field is enabled
 Host  host | ip; Default " "  FTP server's IP address or hostname
 Retry count  2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10; Default: 2  Specifies the maximum number of failed attempts after which the router does not try to send the message anymore
 Username  string; Default: " "  Login user name used for authentication to the FTP server
 Password  string; Default: " "  Login password used for authentication to the FTP
 Interval between reports  Week | Month | Year; Default: Week  Specifies how often the reports should be sent
 Weekday | Month day  weekday | month day; Default: Sunday  Specifies the day of the month/week when the logging should take place. This field changes in accordance with Interval between reports
 Hour  integer [1..24]; Default: 1  Specifies on the hour of the day when the logging should take place

Email

 Field Name
 Value  Description
 Enable  yes | no; Default: no  Toggles the log file report rule ON or OFF
 Events log  System | Network | All; Default: System  Specifies which log to transfer
 Transfer type  Email | FTP; Default: Email  Specifies whether to transfer the log(s) to FTP or Email
 Compress file
 yes | no; Default: no  Compress events log file using gzip
 Subject  string; Default: " "  Specifies the subject of the email log message
 Message  string; Default: " "  The text contained in the log email. This has nothing to do with the log itself, which will be sent as an attached file
 SMTP server  ip | host; Default: " "  Sender's email service provider's SMTP server. If you don't know the SMTP server's address, you can easily look it up online since it is public information
 SMTP server port
 integer [0..65535]; Default: " "  Sender's email service provider's SMTP server. If you don't know the SMTP server's address, you can easily look it up online since it is public information
 Secure connection  yes | no; Default: no  Toggles secure connection feature ON or OFF (use only if the email service provider's server supports SSL or TLS)
 Username  string; Default: " "  Sender's email account's login username
 Password  string; Default: " "  Sender's email account's login password
 Sender's email address  email; Default: " "  The email address of the sender, i.e., the report message will be sent from this email. Make sure this is the same email that you provided login information to
 Recipient's email address  email; Default: " "  The intended recipient's email address. To add more than one email address, click the green  plus symbol located to the right of this field
 Interval between reports  Week | Month | Year; Default: Week  Specifies how often the reports should be sent
 Weekday | Month day  weekday | month day; Default: Sunday  Specifies the day of the month/week when the logging should take place. This field changes in accordance with Interval between reports
 Hour  integer [1..24]; Default: 1  Specifies on the hour of the day when the logging should take place