BEAM iSERIES WebUI - TR-069




Summary

TR-069 (Technical Report 069) is an application layer protocol designed for management of equipment connected to a remote network.

This page is an overview of the TR-069 section of BEAM iSERIES routers.

TR-069 Client Configuration


Field Value Description
Enable yes | no; default: no Turns TR-069 client on or off.
Periodic enable yes | no; default: yes Turns periodic data transmissions to server on or off.
Accept server request yes | no; default: no When enabled the router accepts connection requests from server.
Sending interval integer [60..9999999]; default: 100 Periodic data transmission frequency (in seconds).
Username string; default: easycwmp Username used for authentication to a TR-069 server.
Password string; default: easycwmp Password used for authentication to a TR-069 server.
URL host | ip; default: http://192.168.1.110:8080/openacs/acs IP address or hostname of a TR-069 server.

Management via TR-069

TR-069 can be used to set or get values from RUT routers. Below is a list of commands used for router management via TR-069.

  • R - read only;
  • RW - read/write;
  • string(64) - 64 bit string;
  • string(256) - 256 bit string;
  • unsignedInt - integer storing only positive values.

FW Upgrade:

 
1. FileType - firmware Upgrade Image, string(64) 2. URL - URL, specifying the source file location, string(256) 3. Username - username to be used by the CPE to authenticate with the file server. This string is set to the empty string if no authentication is required, string(256) 4. Password - password to be used by the CPE to authenticate with the file server. This string is set to the empty string if no authentication is required, string(256) 5. FileSize - the size of the file to be downloaded in bytes, unsignedInt

Device Information:

 1. 
DeviceInfo.SpecVersion - R 2. DeviceInfo.ProvisioningCode - RW 3. DeviceInfo.Manufacturer - device manufacturer (e.g., Teltonika) R 4. DeviceInfo.ManufacturerOUI - R 5. DeviceInfo.ProductClass - device model (e.g., RUT950) R 6. DeviceInfo.SerialNumber - device serial number (e.g., 1000111111) R 7. DeviceInfo.HardwareVersion - device hardware version (e.g., 0505) R 8. DeviceInfo.SoftwareVersion - device software version (e.g., RUT9XX_R_00.06.03.2) R 9. DeviceInfo.UpTime - router uptime R 10. DeviceInfo.DeviceLog - last line of device log. R 11. DeviceInfo.MemoryStatus 11.1 DeviceInfo.MemoryStatus.Total - total device memory (e.g., 61008) R 11.2 DeviceInfo.MemoryStatus.Free - free memory (e.g., 24224) R

IP Ping Diagnostics support:

 1. 
IPPingDiagnostics 1.1 IPPingDiagnostics.DiagnosticsState - diagnostics State (e.g. None) R 1.2 IPPingDiagnostics.Host - host RW 1.3 IPPingDiagnostics.NumberOfRepetitions - number of repetitions RW 1.4 IPPingDiagnostics.Timeout - timeout RW 1.5 IPPingDiagnostics.DataBlockSize - data block size RW 1.6 IPPingDiagnostics.SuccessCount - success count R 1.7 IPPingDiagnostics.FailureCount - fail count R 1.8 IPPingDiagnostics.AverageResponseTime - average response time R 1.9 IPPingDiagnostics.MinimumResponseTime - minimum response time R 1.10 IPPingDiagnostics.MaximumResponseTime - maximum response time R

Mobile Information:

 1.
MobileInfo 1.1 MobileInfo.RSSI - GSM signal level R 1.2 MobileInfo.ConnState - connection state R 1.3 MobileInfo.NetState - network link state R 1.4 MobileInfo.ICCID - SIM ICCID R 1.5 MobileInfo.IMSI - IMSI R 1.6 MobileInfo.RSCP - RSCP level R 1.7 MobileInfo.ECIO - EC/IO level R 1.8 MobileInfo.RSRP - RSRP level R 1.9 MobileInfo.SINR - SINR level R 1.10 MobileInfo.RSRQ - RSRQ level R 1.11 MobileInfo.CellID - CellID R 1.12 MobileInfo.Operator - mame of operator used R 1.13 MobileInfo.OperatorNum - operator number R 1.14 MobileInfo.ConnType - data carrier type R 1.15 MobileInfo.Modem 1.15.1 MobileInfo.Modem.Model - modem model R 1.15.2 MobileInfo.Modem.Manufacturer - modem manufacturer R 1.15.3 MobileInfo.Modem.Serial - modem serial number R 1.15.4 MobileInfo.Modem.Revision - modem revision number R 1.15.5 MobileInfo.Modem.IMEI - modem IMEI R 1.15.6 MobileInfo.Modem.SimState - SIM card state R 1.15.7 MobileInfo.Modem.PinState - PIN state R 1.15.8 MobileInfo.Modem.Temperature - modem temperature in 0.1 degrees Celsius R 1.16 MobileInfo.SentToday - bytes sent today R 1.17 MobileInfo.ReceivedToday - bytes received today R 1.18 MobileInfo.SentThisMonth - bytes sent this month R 1.19 MobileInfo.ReceivedThisMonth - bytes received this month R

WAN Information:

 1.
WANConnectionDevice 1.1 WANConnectionDevice.WANIPConnection 1.1.1 WANConnectionDevice.WANIPConnection.ConnectionStatus - connection status (e.g., Connected) R 1.1.2 WANIPConnection.ExternalIPAddress - IP address R 1.1.3 WANIPConnection.MACAddress - MAC address R 1.2 WANConnectionDevice.WANPPPConnection - PPP connection 1.2.1. WANConnectionDevice.WANPPPConnection.1.Enable - connection state (e.g., 1 or 0) R 1.2.2. WANConnectionDevice.WANPPPConnection.1.APN - APN R 1.2.3. WANConnectionDevice.WANPPPConnection.1.ExternalIPAddress - IP address R

WiFi Information:

 1. 
Radio 1.2 Radio.Enable - enabled (e.g., 0 or 1) RW 1.3 Radio.Status - WiFi status (e.g., Up) R 1.4 Radio.Name - Device name R 1.5 Radio.SupportedFrequencyBands - supported frequency bandss (e.g., 2.4GHz) R 1.6 Radio.OperatingFrequencyBand - operating frequency bandss (e.g., 2.4GHz) R 1.7 Radio.ChannelsInUse - channels R 1.8 Radio.Channel - channel in use RW 1.9 Radio.AutoChannelSupported - auto channel support (e.g., 1) R 1.10 Radio.AutoChannelEnable - auto channel state (e.g., 1) RW 1.11 Radio.OperatingStandards - operating standards (e.g., 11ng) RW 2. SSID 2.1 SSID.Enable - WiFi interface state (e.g., 1) RW 2.2 SSID.Status - WiFi interface status (e.g., 1) R 2.3 SSID.Name - interface name (e.g., wlan0 ) R 2.4 SSID.SSID - SSID RW 3. Security 3.5 Security.ModesSupported - (None,WEP-64,WEP-128,WPA-Personal,WPA2-Personal,WPA-WPA2-Personal,WPA-Enterprise,WPA2-Enterprise,WPA-WPA2-Enterprise) R 3.6 Security.ModeEnabled - current mode (e.g WPA2-Personal) RW 3.7 Security.WEPKey - WEP key RW 3.8 Security.PreSharedKey - pre-shared key RW 3.9 Security.KeyPassphrase - key passphrase RW

Hotspot information:

 1. 
General 1.1 General.Enable - state (e.g. 1) RW 1.2 General.IP - IP address (e.g. 192.168.2.254) RW 1.3 General.Mode - authentication mode (extrad - External radius, intrad - Internal radius, norad - Without radius, add - Advertisement, mac - MAC auth, sms - SMS OTP) (e.g., norad) RW 1.4 General.ExternalLandingPage - enable external landing page (e.g., 1) RW 1.5 General.LandingPageAddress - external landing page address (e.g., www.landingpageaddr.com) RW 1.6 General.HTTPSRedirect - enable HTTPS redirect RW 2. Radius 2.1 Radius.Server1 - first radius server address RW 2.2 Radius.Server2 - second Radius server address RW 2.3 Radius.AuthenticationPort - authentication port RW 2.4 Radius.AccountingPort - accounting port RW 2.5 Radius.RadiusSecretKey - radius secret key RW 2.6 Radius.UAMPort - UAM port RW 2.7 Radius.UAMUIPort - UAM UI port RW 2.8 Radius.UAMSecret - UAM secret RW 2.9 Radius.NASIdentifier - NAS identifier RW 2.10 Radius.SwapOctets - swap octets RW 2.11 Radius.LocationName - location name RW

Management server information:

 1. 
ManagementServer.URL - server url (e.g., http://192.168.1.110:8080/openacs/acs) RW 2. ManagementServer.Username - username (e.g., easycwmp) RW 3. ManagementServer.Password - password (e.g., easycwmp) RW 4. ManagementServer.PeriodicInformEnable - enable periodic inform (e.g., 1 or 0) RW 5. ManagementServer.PeriodicInformInterval - interval (e.g, 100) RW 6. ManagementServer.PeriodicInformTime - inform time (e.g, 0001-01-01T00:00:00Z) RW